Laboratory Automatic Environmental Shock Thermal Test Chamber
Customizable
Product Description:
Product use: The machine is used to test the bearing extent of the
material structures and composite material in an instant and
continuous high temperature and extremely low temperature
environment, which is in the shortest time to test its thermal
expansion and contraction caused by chemical change or physical
harm.
The equipment is widely used in metal, plastic, rubber, electronics
and other materials and it can be used as an important reference
for improving product quality. It meets the standard of MTL, IEC,
JIS, GJB…
Features:
(1). With disk USB recording function, no recorder is required;
(2). Refrigerant servo valve flow calculation control. Power saving
30%;
(3). High temperature and high humidity test to prevent
condensation, dripping water technology industry first
(4) In the low temperature working state, the heater does not
participate in the work, and the refrigerant flow and flow
direction of the refrigeration unit are controlled and adjusted by
PWM technology, and the three-way flow of the refrigeration
pipeline, cold bypass pipeline and hot bypass pipeline is adjusted
to realize the temperature control of the working chamber.
automatic constant. In this way, under low temperature conditions,
A 40% reduction in energy consumption can be achieved.
(5) Temperature synchronous rise and fall slope control
(IEC68-2-56, 68-2-30), no dripping, no condensation and
condensation.
(6) Refrigeration advantages: traditional equipment low temperature
control method: Ø Refrigeration compressor start and stop control
temperature (temperature fluctuation is large, which seriously
affects compressor life,
Obsolete technology) Ø Constant operation of refrigeration
compressor + heating PID control (causing cooling capacity and
heating to offset to achieve temperature dynamic balance
Waste a lot of electric energy) • New PWM cold control technology
realizes low temperature energy-saving operation: The new PWM cold
control technology realizes
Main Parameters:
| Capacity (L) | 64 | 80 | 100 | 150 |
| Inner box size (W*H*D)mm | 400x400x400 | 500x400x400 | 500x400x500 | 500x600x500 |
| High temperature room | Preheating temperature range | +60ºC~+220ºC |
| Heating time | RtºC~+150ºC/5Min |
| Low temperature room | Pre-cooling temperature range | -10ºC~-80ºC |
| Cooling time | RtºC~-55ºC/5MinRtºC~-65C/5Min |
| Studio | Temperature shock range | -65ºC~+200ºC |
| Temperature fluctuation | ±1.0ºC |
| Temperature uniformity | ±2ºC |
| Conversion time | 8sec |
| Temperature recovery time | 5Min |
| Inner box material | SUS304# stainless steel plate |
| Outer box material | SUS304# matte brushed stainless steel plate |
| Insulation material | a. High temperature tank: aluminum silicate insulation cotton: b.
Low temperature tank: high density PU foam |
| Test Rack | Stainless Steel Rack |
| Structure | high temperature area, low temperature area, test area |
| Valve unit | Forced air unit valve |
| Refrigeration system | two-stage |
| Cooling method: | semi-hermetic two-stage compressor (water-cooled) / fully-closed
two-stage compressor (air-cooled) |
| Controller: | South Korea "TEMI" or Japan "OYO" brand optional |
| Compressor: | French "Taikang" or independent research and development |
| Protection device: | no fuse switch, compressor high and low pressure protection switch,
refrigerant high pressure protection switch, fault warning system,
electronic alarm |
| Accessories: | viewing window (special optional type), two upper and lower
adjustable compartments, power-on line hole, casters, horizontal
bracket |
| Power supply | AC380V50HZ/60HZ3f |
| Remarks: | The temperature shock test chamber can also be designed according
to the customer's requirements |
(The table parameters for the company Standard Model parameters, we
support customer customization parameters)
Customer Support Services:
Ø Installation
Ø Training (Training customer employees)
Ø Calibration
Ø Preventative maintenance
Ø Replacement parts
Ø Assistance via phone or internet
Ø On-site diagnosis and repair/online diagnosis and repair
